Kromschroeder 88670975 BCU560QC0F0U0D0K1-E burner control unit
Kromschroder 88670975 BCU560QC0F0U0D0K1-E gas control unit designed to control and manage gas burners in intermittent or continuous operation modes. The outputs, such as fans, servo drives, and valves, are connected to the burner control system through a replaceable power module. All necessary parameters for operation are stored on a built-in chip card for parameterization. The controlled outputs for driving and valves are located in the removable power module. If necessary, it can be easily replaced. Krom schroder 88670975 BCU560QC0F0U0D0K1-E control unit can be installed on a DIN rail in a control cabinet. The removable terminal blocks on the BCU simplify installation and removal. Kromschroeder 88670975 BCU560QC0F0U0D0K1-E control box external operator control panel is available as an option for the burner control systems. Kromschroder 88670975 BCU560QC0F0U0D0K1-E gas burner control unit can be installed in the control cabinet door instead of standard control blocks. Messages about program status or faults can be read on the BCU. For adjusting the burner, working points can be conveniently accessed in manual mode using the operator control panel. Kromschroder 88670975 BCU560QC0F0U0D0K1-E gas burner control box designed to provide reliable and efficient control of gas burners. With their modular design, they can be easily integrated into existing control systems and can be used in a wide range of applications, from small to large-scale industrial processes. Kromschroder 88670975 BCU560QC0F0U0D0K1-E automatic gas firing device equipped with advanced features, such as automatic ignition and flame failure detection, which ensure safe and reliable operation of the burners. The systems also have a built-in diagnostic function, which allows for easy troubleshooting and maintenance. Kromschroeder 88670975 BCU560QC0F0U0D0K1-E gas burner control box technical data: With UV sensor or ionization sensor, for continuous operation (intermittent operation with UVS) Flame signal current: ionization control: 2 – 25 μA, UV control: 5 – 25 μA Signal cable for flame signal current: max. 100 m (164 ft) The fail-safe outputs (valve outputs V1, V2 and V3) are monitored for correct functioning and are thus not subject to a max. number of operating cycles Actuator (terminals 53, 54 and 55): max. 1000000, signaling contact for operating signals: max. 1000000, signaling contact for fault signals: max. 10000, On/Off button: max. 10000, Reset/Information button: max. 10,000 Weight: 0.7 kg Ambient temperature: -20 to +60°C (-4 to +140°F), no condensation permitted Enclosure: IP 20 pursuant to IEC 529 Installation location: min. IP 54 (for installation in a control cabinet) Standard version EU certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e) Mains voltage: 120 V AC, 50/60 Hz No valve proving system No capacity control Flammen?berwachung mit Ionisations- oder UV-Signal Screw connection terminals Individual packaging Flame control: ionization 01 Switch-off threshold, burner/pilot burner: 2 micro A 07 Burner/pilot burner start-up attempts: 1 09 Restart: no Safety time during operation: 1 s 52 Relief valve (VPS): V2 61 Minimum burner on time tB: 0 s 62 Minimum pause time tBP: 0 s 67 Operating time in Manual mode limited to 5 min. 77 User-defined password 78 Burner application: burner 94 1st safety time on start-up: 3 s 95 Flame proving period 1 tFS1: 2 s 80 Fieldbus communication: with address check