Kromschroder وحدة التحكم في الموقد من شركة Kromschroeder BCU570WC1F1U0K2-E (88660022)

Kromschroder 88660022 BCU570WC1F1U0K2-E gas burner control unit designed to monitor and regulate the operation of high-power blow-off nozzles with smooth, continuous adjustment in intermittent or continuous mode. Kromschroder 88660022 BCU570WC1F1U0K2-E automatic gas firing device design allows for the connection of error-protected outputs, fan direction, servomotors, and valves, enabling precise control over the burner. All necessary operating parameters are stored on an integrated chip-based parameterization card, ensuring seamless operation and minimizing the risk of errors. Kromschroder BCU570WC1F1U0K2-E 88660022 automatic gas firing device technical data Flame control: with UV sensor or ionization sensor For intermittent or continuous operation Flame signal current: ionization control: 1–25 μA, UV control: 1–35 μA Ionization cable, UV cable: max. 100 m (164 ft) Number of operating cycles: The fail-safe outputs (valve outputs V1, V2, V3 and V4) are monitored for correct functioning and are thus not subject to a max. number of operating cycles Control actuator (terminals 53, 54 and 55): max. 250 000, signaling contact for operating signals: max. 250 000, signaling contact for fault signals: max. 10 000, On/Off button: max. 10 000, Reset/Information button: max. 10 000 Weight: 0.93 kg Dimensions (W × H × D): 102 × 115 × 112 mm Connections: Screw terminals: nominal cross-section 2.5 mm², wire cross-section (rigid) min. 0.2 mm², wire cross-section (rigid) max. 2.5 mm², wire cross-section AWG/kcmil min. 24, wire cross-section AWG/kcmil max. 12 Spring force terminals: nominal cross-section 2 x 1.5 mm², wire cross-section min. 0.2 mm², wire cross-section AWG min. 24, wire cross-section AWG max. 16, wire cross-section max. 1.5 mm², rated current 10 A (8 A UL), to be observed in case of daisy chain Environment Storage temperature: -20 to +60°C (-4 to +140°F) Ambient temperature: -20 to +60°C (-4 to +140°F), no condensation permitted Enclosure: IP 20 pursuant to IEC 529 EU certified, certified for systems up to SIL 3 (compliant with PL e) Mains voltage: 230 V AC, 50/60 Hz With valve proving system Modulating capacity control with interface for actuator IC Flammen?berwachung mit Ionisations- oder UV-Signal Spring force connection terminals Individual packaging Flame control: ionization 01 Burner switch-off threshold: 2 micro A 07 Burner start-up attempts: 3 09 Restart: no 13 Low pressure cut-off with fault lock-out 15 Air deficiency cut-out with fault lock-out 19 Safety time during operation: 1 s 40 Capacity control with IC 20 30 Fan run-up time tGV: 0 s 32 Air flow monitoring during controlled air flow on, maximum capacity 33 Start-up with pre-purge: yes (depending on P34 Pre-purge time tPV) 34 Pre-purge time tPV: 0 s 37 Post-purge time tPN: 6000 s 44 Controller enable signal delay time tRF: 0 s 51 Valve proving system: tightness test before start-up 52 Relief valve (VPS): V3 56 Measurement time Vp: 30 s 59 Valve opening time V1 (tL1): 2 s 61 Minimum burner on time tB: 0 s 62 Minimum pause time tBP: 0 s 63 Switch-on delay time tE: 0 s 67 Operating time in Manual mode limited to 5 min. 77 User-defined password 78 Burner application: burner 79 Pilot burner: with shut-down 80 Fieldbus communication: no address check 93 Pre-ignition time tVZ: 1 s 94 1st safety time on start-up: 3 s 95 Flame proving period 1 tFS1: 2 s Kromschroeder BCU570WC1F1U0K2-E 88660022 gas burner safety control box designed lifetime The lifespan of Krom schroder 88660022 BCU570WC1F1U0K2-E control unit depends on the operating conditions and may vary depending on the specific situation. In general, Kromschroder 88660022 BCU570WC1F1U0K2-E control box is a high-quality component that can ensure safe and efficient operation of the combustion system for many years. However, as the lifespan of critical components expires, it may be necessary to replace them. This is particularly important in the case of Kromschroeder 88660022 BCU570WC1F1U0K2-E gas burner control box, which is a key component of the combustion system. In any case, it is recommended to regularly inspect Kromschroder 88660022 BCU570WC1F1U0K2-E gas burner control unit for signs of wear and damage, and replace it if necessary. This will help ensure safe and efficient operation of the combustion system for many years.